LTBA RNAV Error for 35R in AIRAC Cycle 1702

This forum answers all questions about products before you decide to become a subscriber.

Moderator: Ian

Post Reply
watauga
Posts: 4
Joined: Wed Jun 21, 2017 1:34 am
Contact:

LTBA RNAV Error for 35R in AIRAC Cycle 1702

Post by watauga » Wed Jun 21, 2017 2:57 am

I have AIRAC cycle 1702 through my purchase of the Eclipse 550 NG. While flying from LTAC to LTBA I was directed to land on rwy 35R. I chose to use the RNAV final for this landing. This choice guided the plane to land on rwy 17L. Below is the RNAV for rwy35R routing from the Proc folder. The VURAL from charts I have seen appears to be for RNAV 17L. Per the RNAV routing for rwy 35L and 35R below both appear to have headings of 174 for the approach. This same issue may also be occurring at RNAV rwy 23. See below. I have provided the final for RNAV 17L at the bottom. It appears to be the same as the final for RNAV 35R. Have these final approached been corrected in cycle 1706? If so, will you send me the corrections for LTBA?

Thanks for your help.
Ron West
KBNA

FINAL,R35R-M,35R,R,3
IF,CD174,41.161381,28.801311,IST,354.0,12.0,2,3000,0,0,0,0,0,0
CF,VURAL,41.094722,28.804722,0,IST,354.1,8.0,174.0,4.0,2,1800,0,0,0,0,2,0
CF,MD174,41.028050,28.807478,0,IST,354.0,4.0,174.0,4.0,1,1100,0,0,0,0,3,0
FA,MD174,41.028050,28.807478,0,IST,0.0,0.0,174.0,2,2500,0,0,0,0,0,0
DF,CEK,41.006556,28.528611,2, ,0.0,0.0,1,5000,0,0,0,0,0,0
HM,CEK,41.006556,28.528611,1, ,0.0,0.0,90.0,04.3,0,0,0,1,230,0,0,0,0


FINAL,R35L-M,35L,R,3
IF,CD174,41.161381,28.801311,IST,354.0,12.0,2,3000,0,0,0,0,0,0
CF,VURAL,41.094722,28.804722,0,IST,354.1,8.0,174.0,4.0,2,1800,0,0,0,0,2,0
CF,MD174,41.028050,28.807478,0,IST,354.0,4.0,174.0,4.0,1,1100,0,0,0,0,3,0
FA,MD174,41.028050,28.807478,0,IST,0.0,0.0,174.0,2,2500,0,0,0,0,0,0
DF,CEK,41.006556,28.528611,2, ,0.0,0.0,1,5000,0,0,0,0,0,0
HM,CEK,41.006556,28.528611,1, ,0.0,0.0,90.0,04.3,0,0,0,1,230,0,0,0,0

FINAL,R23-M,23,R,3
IF,CD174,41.161381,28.801311,IST,354.0,12.0,2,3000,0,0,0,0,0,0
CF,VURAL,41.094722,28.804722,0,IST,354.1,8.0,174.0,4.0,2,1800,0,0,0,0,2,0
CF,MD174,41.028050,28.807478,0,IST,354.0,4.0,174.0,4.0,1,1100,0,0,0,0,3,0
FA,MD174,41.028050,28.807478,0,IST,0.0,0.0,174.0,2,2500,0,0,0,0,0,0
DF,CEK,41.006556,28.528611,2, ,0.0,0.0,1,5000,0,0,0,0,0,0
HM,CEK,41.006556,28.528611,1, ,0.0,0.0,90.0,04.3,0,0,0,1,230,0,0,0,0

FINAL,R17L-M,17L,R,3
IF,CD174,41.161381,28.801311,IST,354.0,12.0,2,3000,0,0,0,0,0,0
CF,VURAL,41.094722,28.804722,0,IST,354.1,8.0,174.0,4.0,2,1800,0,0,0,0,2,0
CF,MD174,41.028050,28.807478,0,IST,354.0,4.0,174.0,4.0,1,1100,0,0,0,0,3,0
FA,MD174,41.028050,28.807478,0,IST,0.0,0.0,174.0,2,2500,0,0,0,0,0,0
DF,CEK,41.006556,28.528611,2, ,0.0,0.0,1,5000,0,0,0,0,0,0
HM,CEK,41.006556,28.528611,1, ,0.0,0.0,90.0,04.3,0,0,0,1,230,0,0,0,0

User avatar
Ian
Posts: 3349
Joined: Mon Nov 26, 2012 4:43 pm
Contact:

Re: LTBA RNAV Error for 35R in AIRAC Cycle 1702

Post by Ian » Thu Jun 22, 2017 1:56 am

Hi Ron,

Welcome.

Thank you for reporting this. We are investigating.

Cheers
Ian
Image

User avatar
navdata
Posts: 1620
Joined: Fri Jun 14, 2013 2:49 pm
Contact:

Re: LTBA RNAV Error for 35R in AIRAC Cycle 1702

Post by navdata » Thu Jun 22, 2017 5:17 pm

Hi Ron,
I have looked deeper into it and this procedures (which is not really a RNAV procedure - and that's really an issue) is a Circle-To-Land procedure (CVDM), which is the VORTAC procedure into LTBA. As you possible know, a CTL procedure has no runway-identifier, and second no addon can handle such procedures without a runway-ident. So, the "workaround" is to duplicate such procedures to all runways - therefore the double entries on all possible runways. What is wrong, and that's correct it's not a RNAV procedure it's a VORTAC procedure - I will fix it and you can expect this change with the next release.
Thanks for the report Ron!
Kind regards,
Richard

Image

watauga
Posts: 4
Joined: Wed Jun 21, 2017 1:34 am
Contact:

Re: LTBA RNAV Error for 35R in AIRAC Cycle 1702

Post by watauga » Fri Jun 23, 2017 2:22 am

Good morning Richard,

Thank you for the update. Happy to help with perfecting your product.

Regards,
Ron West
KBNA

Post Reply

Return to “Pre-purchase Questions”

Who is online

Users browsing this forum: No registered users and 2 guests